JoJoHobbyNStuff

Thursday, August 17, 2017

HG Zaku II High Mobility Type Reuse P Device


Introduction:

This kit was completed as a free commission to the winner of my Patreon launch contest! The Winner Gabriel Z. requested a HG Psycho Zaku painted with Char custom color scheme. This was a great kit to build as a commission, because it's a model that I would have never purchased for myself. And, despite some misgivings I had about the design of the model and the inclusion of five dozen vernier nozzles; it turned out to be a pretty fun kit with cool final design. This isn't a model I would recommend to a novice builder, but I'm positive a intermediate or advanced modeler would be up to the challenge.

Lore wise I can think of this design existing in an alternate Gundam timeline. Maybe Char's initial conflict with the Gundam resulted in him being severely injured. After recovery he might find himself being willingly (or otherwise) inducted into the Living Dead Unit. I wouldn't be surprised to find him surpassing the other pilots of the unit and finding himself as the test pilot for the Psycho Zaku.

Kit Talk:


First things first; this kit had a lot of seam lines that needed to be fixed. Each, bazooka, rifle, fuel tank and panzerfaust has a big ugly seamline running the length of the part. The seamlines on each fuel tank were poorly matched and required a bit of sanding an puttying to even everything out.

The vernier nozzles were also worrisome, as the smallest nozzles barley measured 2 mm in each dimension. If you drop one of these pieces I guarantee that it will vanish! I painted each nozzle in two colors. I used a silver interior color and a neutral gray exterior. I will likely do something similar using gold on my MG when I get around to it.



I modified one set of Nozzles on the backside of the legs. I did this by drilling out the low detail molds on each side. I applied Tamiya thin cement to the drilled area to smooth out the drill marks and later inserted a Kotobukiya nozzle into the gap to fill out the space.



Unfortunately during final construction one of the chest pipes snapped. This wasn't entirely unexpected due to the design of the part. However this at least allows me to show a solution to properly fix this break.



The chest pipes are made of the same hard plastic as the frame, but feature a series of slices to allow the part to gradually curve. There isn't enough surface area to properly glue this joint back in place and expect it to hold.



I used a thin steel rod (get these from the hardware store) and a pin vice to drill a hole.



The rod is bent into shape and inserted into both ends of the pipe.



Colors used in the build are Gundam Color Char Pink & Red, Mr. Color Navy Blue and Gaia Colors Neutral gray 2 and 4. Other colors like silver, clear red, white, yellow and orange were also used minimally for small details. The only thing I regret is that this kit does not include a second 'deactivated' heat hawk like the recent HG Origin kits; I opted to paint the heat hawk in it's activated state (because it looks cooler that way), despite still being holstered.

A fair bit of masking was required to add the white stripe to the shoulder, and the light gray bands across the fuel tanks and bazookas. I also took the time to mask and paint the small vernier details on the lower legs. The silver lips on these areas were applied by hand using Vallejo silver and a toothpick.

Decals for this kit were taken from the RG Char Zaku II and the HG Gundam The Origin decal sheets. The decals scheme I chose to apply was fairly reserved due to the complexity of the design of the mobile suit.



If you're interested in picking up this or other kits consider purchasing through the Amazon links on my site. Every purchase you make helps me out tremendously and doesn't cost you a dime!

Wednesday, August 16, 2017

MG Providence Gundam alternative gundam scheme


For those not in the know, there's a second set of decals available for the MG Providence Gundam. I recently purchased a set of 3rd party decals including these decals but I had no scheme to apply them to! Thankfully Saintism had my back and shared a scanned copy of this p-bandai manual including this scheme!

If you need this scheme for your build click the image and right click to save it to your machine!

Check out Saint's website here: http://www.saint-ism.com/